Видео

@19:00 I have successfully soldered thermal fuses many times, just be quick, get the wire hot first, and hold between the join and the fuse with something to heat sink it.

Good job. It might have just had a voltage surge through the house. We use our air frier all the time. Great style of cooker.

Great review! Did you ever tried the USB-C ?

Hi. do you have the value of the capacitor?

The world's most fancy wrist watch! 😁😎

On crusty TH connections I usually remove as much of the old solder as possible, then use fresh solder to make whole new joints.

I wonder if that is zero lead solder, horrible stuff

Good job, it doesn't look very water proof to me

Interesting, Ive always wanted to have a look at one of those, they say the are water proof so interesting to see how good these really are if left outside. I too was told about the effects of cutting leads affecting the components, I believe that came from Nasa but like you Ive never had any problems but Ive never worked on spaceships either. Im a subscriber now :) Where are you in NZ, Im in Wellington, Silverstream actually.

I would be inclined to wire up a silent 120mm fan inside, that runs around 9v to keep the noise down and constantly cool the components, Interestingly you can pick this PS up for $ 111 delivered now

The Battery cable has a connector mid-way between where it enters the chassis. You have to un-wrap the black foam at the thickest part of the battery cable, and underneath are white 5-Pin connectors that are easily UN-plugged. Then you can be remove the battery. Save the foam and re wrap the connector when you re-install it so that it doesn't rattle to the BASS!

Must have been shorting to the earthed casing, have to wonder if the house it was used in has an electrical issue where the earth leakage isn't working or maybe not even present due to age pre-dating the use of RCD's.

@1:00 I would be using a flat blade screwdriver for that, being as it requires more force than the spudger can manage.

The power supply looked like a standard capacitive dropper. The large X2 film caps often fail (low capacitance) which causes no or erratic operation.

Momentary switch isn’t soldered at all on that side

You could get a MELF zener assortment, I picked one up a while ago for this kind of situation, used them a few times.

Shame - you didn't check the gigantic orange glowing resistor on the front, mind your fingers! Stay warm.

We have the same issue . Thank you !!

Great job buddy John did you have to program that chip in anyway. Many thanks Tom

Thanks Jonny and thank everyone for your comments. I have the same issue with my 2013 Hilux.... Will give this a bash this week...

Can I have it replaced??

I am amazed! never seen a "conductive" dust let alone dark!! Nice work!

Do you repair for the public?

Hey mate I bought cluster from eBay as can fg mk2 done 89k only buy cluster I bought its was from same model and year but has over 200k. Any way to fix the odo reading. And if I directly put new one which I bought without correction any kms. Do I need to get any calibration.l to make working with my car ??

Guess who just purchased some tin snips....

@10:40 they look familiar...

yay a boring video about a radio scanner.

Maybe from vaping. That vape juice is nasty stuff! Great job!

MAAAAAAATTEEEEEE!!!!!!!!! You're a dead-set champion.... Just fault-found following your instructions and lo and behold it was the same dioide... Repaired, and I now have my Acoustimass back online!!! Very, very much appreciated bud. 😍

Nice. What’d you use to clean?

Reminds me of ruclips.net/video/dftkoD7LG0A/видео.html, where the gunk used to glue down components turned conductive...

This was an episode of CSI: Jonny Fix. The victim PS5. The killer - Mary Jane. Case Solved.

May have been effecting a voltage divider on the sense side for feedback? Certainly an interesting one.

Thanks for the video. It would be helpful to say which side of the speaker the motherboard is on. Also, I got mad and just ripped my side panels off. At this point it shouldn't take me an hour to try and turn it when it doesn't want to turn, and everyone else does it like its a baby toy. You'd think they would have some type of ring to help open the side panels. I butchered mine with pliers and a flathead.

Never buying Bose again. This just happened to me

Can you run spooky 2 software on it mate?

@Jonny Fix do you think there would be any issues if I was to swap the speedo facia with LCD off another cluster onto my FG but keep my original board reason being for aesthetic purposes

DIOS los bendiga

Mine also same problem, my one was broken, I am onboard a ship and my colleague Electrical engineer said that he can’t soldering that small piece. Do u have any suggestions how to find the power charging board for replacement ?

Saludos maestro una buena explicación y como menciono el caballero anterior seria posible poner aluminio o cinta térmica a los capacitores y al que esta debajo también uno pequeño y al chip de su costado por encima al menos proteger del calor para realizar trabajos por horas sin miedo a que dure poco ...

Nice. Do try again.

There is a difference between the colons and the decimal point in the Frequency parametric value; you can't treat the colons as if they are decimal points! The colons are just markers every three orders of magnitude. You had been setting the signal generator outputs to very low voltages; perhaps the one you connected to the frequency counter was set too low to register? The included BNC-to-BNC cable(s) is pretty much crap, and very short. When I used some decent BNC cables on mine, most of the ringing and other distortions on the square wave signal became all but negligible on the 'scope. The Square wave is, by definition, a 50% duty cycle, not adjustable by the user. By default, the rectangle wave is set to 50%, so it looks the same as a square wave; try adjusting the duty cycle to see a difference. The trapezoid wave also needs adjustment of other parameters in order to be distinguished from a square wave.

Can I send my amp to you to fix

My ultrasonic cleaner mechine run very short time and auto off by itselft without compleate tusk which electronics parts I should change?

This bloke must do it for a living..he's taking the needlessly long method.. Just undo the 2 screws on the back and white cover comes off.

Hi! I hope you respond. On the first test, where we use the voltmeter on the power line and 5v , i only get 5 volts when i tap on the power button. What does it mean? Have i done something wrong? Pls, i don't want to trash this great console. Bye

I am a Wantek power supply manufacturer. If you need anything, please feel free to contact me

7:09 Nice...😋😁😁😂

WHAT MOFSET 19V SERI ASUS K55 SIR

The same problem, the diode shorted, thanks for the content 👍🏼